VEOLIA MEMBRAN KATALOG
Etkin Çözümler Sunuyoruz
VEOLIA MEMBRAN KATALOG
VEOLIA MEMBRAN KATALOG
Standard Brackish Water RO Elements
The A-Series, family of proprietary thin-film reverse osmosis elements, are characterized by high flux and high sodium chloride rejection. AG Standard Brackish Water Elements are selected when high rejection and operating pressures as low as 200 psi (1,379 kPa) are desired. These elements allow moderate energy savings and are considered a standard in the industry.
NRTECH
Table 1: Element Specification
Membrane |
A-Series, thin-film membrane (TFM) |
Model |
Average Permeate Flow (1)(2) |
Average NaCl Rejection (1)(2) |
Minimum NaCl Rejection (1)(2) |
AG2540TM |
750 (2.8) |
99.5% |
99.0% |
AG4026F |
1,600 (6.1) |
99.5% |
99.0% |
AG4040C |
2,400 (9.1) |
99.5% |
99.0% |
AG4040FM |
2,400 (9.1) |
99.5% |
99.0% |
AG4040TM |
2,400 (9.1) |
99.5% |
99.0% |
AG8040F |
10,000 (37.9) |
99.5% |
99.0% |
AG8040F 400 |
11,000 (41.6) |
99.5% |
99.0% |
AG8040F 440 |
12,000 (45.4) |
99.5% |
99.0% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.(2) Testing conditions: 2,000 ppm NaCl solution at 225 psi (1,551 kPa) operating pressure, 77°F (25°C), pH 7.5 and 15% recovery.
Table 2: Element Properties (3)
Model |
Membrane Area ft2 (m2) |
Outer Wrap |
Part Number |
AG2540TM |
27 (2.5) |
Tape |
1206729 |
AG4026F |
60 (5.6) |
Fiberglass |
1206756 |
AG4040C |
90 (8.4) |
Cage |
1206757 |
AG4040FM |
85 (7.9) |
Fiberglass |
3032513 |
AG4040TM |
85 (7.9) |
Tape |
3032514 |
AG8040F |
365 (33.9) |
Fiberglass |
3032515 |
AG8040F 400 |
400 (37.2) |
Fiberglass |
3032518 |
AG8040F 440 |
440 (40.9) |
Fiberglass |
3194307 |
Note: **4040C elements do not feature brine seal.
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
NRTECH
Table 3: Dimensions and Weight (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed |
||
A |
B |
C |
Weight lbs. (kg) |
||
AG2540* |
Male |
40.0 (101.6) |
0.75 (1.90) |
2.4 (6.1) |
7 (3) |
AG4026* |
Female |
26.0 (66.7) |
0.625 (1.59) |
3.9 (9.9) |
9 (4) |
AG4040C |
Female |
40.0 (101.6) (1) |
0.625 (1.59) |
3.9 (9.9) |
11 (5) |
AG4040FM |
Male |
40.0 (101.6) |
0.75 (1.90) |
3.9 (9.9) |
11 (5) |
AG4040TM |
Male |
40.0 (101.6) |
0.75 (1.90) |
3.9 (9.9) |
11 (5) |
AG8040F |
Female |
40.0 |
1.125 |
7.9 |
35 |
(101.6) |
(2.86) |
(20.1) |
(16) |
||
AG8040F 400 |
Female |
40.0 |
1.125 |
7.9 |
35 |
(101.6) |
(2.86) |
(20.1) |
(16) |
||
AG8040F 440 |
Female |
40.0 |
1.125 |
7.9 |
35 |
(101.6) |
(2.86) |
(20.1) |
(16) |
Table 4: Operating and CIP Parameters (3)
Typical Operating |
200 psi (1,379 kPa) |
Typical Operating Flux |
10-20GFD (15-35 |
Maximum Operating Pressure |
Tape: 450 Other outerwrap: 600 psi (4,137 |
Maximum Temperature |
Continuous operation: 122°F (50°C) |
pH Range |
Optimum rejection: 7.0-7.5, Continuous operation: 2.0-11.0, Clean-In-Place (CIP): |
Maximum Pressure Drop |
Tape: 7 psi (48 kPa) over Cage and |
Chlorine |
1,000+ ppm x |
Feedwater |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Includes interconnector, refer to Technical Bulletin TB1206.
(5) Refer to Cleaning Guidelines Technical Bulletin TB1194
NRTECH
AK Series FACT SHEET
Low Energy Brackish Water RO Elements
The A-Series family of proprietary thin-film reverse osmosis elements is characterized by high flux and high sodium chloride rejection. AK Low Pressure Brackish Water Elements are selected when high rejection and low operating pressures are desired. These elements allow significant energy savings since good rejection is achieved at operating pressures as low as 100 psi (689 kPa).
Table 1: Element Specification
Membrane |
A-series, thin-film membrane (TFM) |
Model |
Average Permeate Flow gpd (m3/day) (1)(2) |
Average NaCl Rejection (1)(2) |
Minimum NaCl Rejection (1)(2) |
AK2540TM |
750 (2.8) |
99.0% |
98.0% |
AK4040C |
2,300 (8.7) |
99.0% |
98.0% |
AK4040FM |
2,200 (8.3) |
99.0% |
98.0% |
AK4040TM |
2,200 (8.3) |
99.0% |
98.0% |
AK8040F |
10,000 (37.9) |
99.0% |
98.0% |
AK8040F 400 |
11,000 (41.6) |
99.0% |
98.0% |
AK8040F 440 |
12,000 (45.4) |
99.0% |
98.0% |
(1) Average salt rejection after 24 hours operation. Individual flow rate may vary ±20%.
(2) Testing conditions: 500ppm NaCl solution at 115psi (793kPa) operating pressure, 77°F (25°C), pH7.5 and 15% recovery.
Table 2: Element Properties (3)
Model |
Membrane area ft2 (m2) |
Outer |
Part Number |
AK2540TM |
27 (2.5) |
Tape |
1206802 |
AK4040C |
90 (8.4) |
Cage |
1223696 |
AK4040FM |
85 (7.9) |
Fiberglass |
3039082 |
AK4040TM |
85 (7.9) |
Tape |
3039149 |
AK8040F |
365 (33.9) |
Fiberglass |
3039160 |
AK8040F 400 |
400 (37.2) |
Fiberglass |
3039161 |
AK8040F 440 |
440 (40.9) |
Fiberglass |
3194308 |
Note: **4040C elements do not feature brine seal.
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
NRTECH
Table 3: Dimensions and Weight (3)
Model |
Type |
Dimensions, Inches (cm) |
Boxed |
||
A |
B |
C |
Weight lbs. (kg) |
||
AK2540 |
Male |
40.0 (101.6) |
0.75 (1.9) |
2.4 (6.1) |
5 (2.3) |
AK4040C |
Female |
40.0 (101.6) (4) |
0.625 (1.59) |
3.9 (9.9) |
9 (4) |
AK4040FM |
Male |
40.0 (101.6) |
0.75 (1.9) |
3.9 (9.9) |
9 (4) |
AK4040TM |
Male |
40.0 (101.6) |
0.75 (1.9) |
3.9 (9.9) |
9 (4) |
AK8040F |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
AK8040F 400 |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
AK8040F 440 |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
Table 4: Operating and CIP Parameters (3)
Typical Operating Pressure |
100 psi (689 kPa) |
Typical Operating Flux |
10-20 GFD (15-35LMH) |
Maximum Operating Pressure |
600 psi (4,136 kPa) |
Maximum Temperature |
Continuous |
pH Range |
Optimum rejection: 7.0-7.5, Continuous operation: 2.0-11.0, Clean In Place (CIP): |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa) |
Chlorine Tolerance |
1,000+ ppm x hours, dechlorination recommended |
Feedwater |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.(4) Includes interconnector, refer to Technical Bulletin TB1206.(5) Refer to Cleaning Guidelines Technical Bulletin TB1194.
NRTECH
AG H Series FACT SHEET
High performance, very high rejection brackish water RO elements
The AG H Series of reverse osmosis (RO) elementsare designed to perform in brackish water applications where the very highest levels of rejectionare needed. AG H Series elements combine Veolia chemistry and manufacturing advancements to deliver differentiated performance over the life of the element in ionic rejection and in the rejection of uncharged or lightly charged species such as silica. These elements are ideal for applications such as ultrapure water production, treating high pressureboiler feed water, or any other application when the very highest rejection is needed.
All AG H Series elements have NSF/ANSI/CAN 61 certification..
Table 1: Element Specification
Membrane |
Thin-film membrane (TFM), polyamide |
Model |
Average permeate flow gpd (m3/day)(1,2) |
Typical NaCl rejection(1,2) |
Minimum NaCl rejection(1,2) |
AG-90 H |
2,600 (9.8) |
99.8% |
99.65% |
AG-400 H |
11,000 (41.6) |
99.8% |
99.65% |
AG-440 H |
12,000 (45.4) |
99.8% |
99.65% |
Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.(2) Testing conditions: 2,000 ppm NaCl solution at 225 psi (1,550 kPa) operating pressure, 77°F (25°C), pH 7 and 15% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Feed Spacer (mil) |
Part number |
AG-90 H |
90 (8.3) |
Fiberglass |
31 |
3194885 |
AG-400 H |
400 (37.2) |
Fiberglass |
34 |
3150329 |
AG-440 H |
440 (40.9) |
Fiberglass |
28 |
3150328 |
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
NRTECH
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed weight lbs (kg) |
||
A |
B |
C |
|||
AG-90 H |
Male |
40.0 |
0.75 |
3.9 |
9 |
(101.6) |
(1.9) |
(9.9) |
(4) |
||
AG-400 H |
Female |
40.0 |
1.125 |
7.9 |
40 |
(101.6) |
(2.86) |
(20.1) |
(18) |
||
AG-440 H |
Female |
40.0 |
1.125 |
7.9 |
42 |
(101.6) |
(2.86) |
(20.1) |
(19) |
Table 4: Operating and CIP Parameters (3)
Typical Operating Pressure |
200 psi (1,380 kPa) |
Typical Operating Flux |
10-20 GFD (15-35 LMH) |
Maximum Operating Pressure |
600 psi (4,137 kPa) |
Maximum Temperature |
Continuous |
pH range |
Optimum rejection: 7.0-7.5 Continuous operation 2.0-11.0 Clean-In-Place (CIP): |
Maximum Pressure Drop |
Over an element: 15 psi (103 |
Chlorine Tolerance |
1,000+ |
Feedwater2 |
NTU < 1 SDI15 < 5 |
) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.(4) Please refer to Cleaning Guidelines Technical Bulletin TB1194.
Additional Information
• As with any product, use of the products mentioned in this publication in a given application must be tested (including field testing, etc.) by the user in advance to determine suitability.
• Treat RO elements with care; do not drop the element.
• Each RO element is wet tested. The 8-inch diameter elements are preserved in a 1% weight sodium bisulfite solution and vacuum packed in oxygen barrier bags. The 4-inch diameter elements are packaged with oxygen scavenger packets in oxygen barrier bags.
• During storage, avoid freezing and direct sunlight. The temperature should be below 35°C (95°F).
After Installation
• Keep the RO elements wet and use a compatible preservative for storage duration longer than 7 days.
• During the initial start-up, discharge the first permeate to drain for 30 minutes.
• Permeate back pressure should not exceed feed pressure at any time.
• The RO elements shall be maintained in a clean condition, unfouled by particulate matter or precipitates or biological growth.
• Consider cleaning, if the pressure drop increases by 20% or water permeability decreases by 10%. Use only chemicals which are compatible with the membrane.
NRTECH
AK H Series FACT SHEET
High performance, high rejection, and ultra-low energy RO elements
The AK H Series of thin-film reverse osmosis (RO) elements provides all of the features expected of highperformance low energy elements including very high rejection, low operating pressure, and longer element life-times. These AK H Series brackish water elements also offer very high rejection of uncharged and lightly charged species including silica and manymicropollutants. AK H Series elements combine Veolia chemistry and manufacturing advancements to deliver differentiated performance that is ideal for any brackish water salinity with applications such asdrinking water treatment for removal of emergingcontaminants and second-pass RO systems in front of further polishing by ion exchange or electro- deionization.
All AK H Series elements have NSF/ANSI/CAN 61 certification and are a reliable source of energy savings with minimal compromise in contaminantremoval.
Table 1: Element Specification
Membrane |
Thin-film membrane (TFM), polyamide |
Model |
Average permeate flow gpd (m3/day) (1,2) |
Typical NaCl rejection (1,2) |
Minimum NaCl rejection (1,2) |
AK-90 H |
2,250 (8.5) |
99.65% |
99.40% |
AK-400 H |
11,000 (41.6) |
99.65% |
99.50% |
AK-440 H |
12,000 (45.4) |
99.65% |
99.50% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%..
(2) Testing conditions: 500ppm NaCl solution at 115 psi (793 kPa) operating pressure, 77°F (25°C), pH 7 and 15% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Feed Spacer (mil) |
Part number |
AK-90 H |
90 (8.3) |
Fiberglass |
31 |
3194886 |
AK-400 H |
400 (37.2) |
Fiberglass |
31 |
3150326 |
AK-440 H |
440 (40.9) |
Fiberglass |
28 |
3150327 |
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
NRTECH
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed weight lbs (kg) |
||
A |
B |
C |
|||
AK-90 H |
Male |
40.0 |
0.75 |
3.9 |
9 |
(101.6) |
(1.9) |
(9.9) |
(4) |
||
AK-400 H |
Female |
40.0 |
1.125 |
7.9 |
40 |
(101.6) |
(2.86) |
(20.1) |
(18) |
||
AK-440 H |
Female |
40.0 |
1.125 |
7.9 |
42 |
(101.6) |
(2.86) |
(20.1) |
(19) |
Typical Operating Pressure |
P Parameters (3) 100 psi (689 kPa) |
Typical Operating Flux |
10-20 GFD (15-35 LMH) |
Maximum |
400 psi (2,756 kPa) |
Maximum Temperature |
Continuous operation: 122°F (50°C) Clean-In- Place (CIP):122°F (50°C) |
pH Range |
Optimum rejection: 7.0-7.5 Continuous operation: 2.0-11.0 Clean-In-Place |
Maximum Pressure Drop |
Over an element: 15 psi (103kPa) Per housing: 50 psi (345 kPa) |
Chlorine Tolerance |
1,000+ ppm-hours, dechlorination recommended |
Feedwater2 |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Please refer to Cleaning Guidelines Technical Bulletin TB1194.
Additional Information
• As with any product, use of the products mentioned in this publication in a given application must be tested (including field testing, etc.) by the user in advance to determine suitability.
• Treat RO elements with care; do not drop the element.
• Each RO element is wet tested. The 8-inch diameter elements are preserved in a 1% weight sodium bi-sulfite solution and vacuum packed in oxygen barrier bags. The 4-inch diameter elements are packaged with oxygen scavenger packets in oxygen barrier bags.
• During storage, avoid freezing and direct sunlight. The temperature should be below 35°C (95°F).
After Installation
• Keep the RO elements wet and use a compatible preservative for storage duration longer than 7 days.
• During the initial start-up, discharge the first permeate to drain for 30 minutes.
• Permeate back pressure should not exceed feed pressure at any time.
• The RO elements shall be maintained in a clean condition, unfouled by particulate matter or precipitates or biological growth.
• Consider cleaning, if the pressure drop increases by 20% or water permeability decreases by 10%. Use only chemicals which are compatible with the membrane.
NRTECH
AG FR H Series FACT SHEET
High performance, fouling resistant, high rejection brackish water RO elements
The AG FR H Series of thin-film reverse osmosis (RO) elements are designed to perform in challenging brackish water applications where high rejection is critical and fouling remains a key consideration. AG FR H Series elements combine Veolia chemistry and manufacturing advancements to deliver differentiated performance over the life of the element both in ionic rejection and in the rejection of uncharged or lightly charged species such assilica. Fouling resistance was also integrated into themembrane chemistry and element design for an optimized, long lasting, high performance element that is used in industries such as chemicals, mining, steel, and coal-to-chemicals.
All AG FR H Series membranes have NSF/ANSI/ CAN 61 certification for use in challenging municipalapplications such as surface water treatment for drinking water with intent to remove emerging contaminants such as PFAS (per- and polyfluoroalkyl substances) compounds with a wide spectrum of size and structure.
Table 1: Element Specification
Membrane |
Thin-film membrane (TFM), polyamide |
Model |
Average permeate flow (1,2) |
Typical NaCl rejection (1,2) |
Minimum NaCl rejection (1,2) |
AG-400 FR H |
11,000 (41.6) |
99.8% |
99.5% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.
(2) Testing conditions: 2,000 ppm NaCl solution at 225 psi (1,550 kPa) operating pressure, 77°F (25°C), pH 7 and 15% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Feed Spacer (mil) |
Part number |
AG-400 FR H |
400 (37.2) |
Fiberglass |
34 |
3187651 |
Figure 1: Element Dimensions Diagram – Female
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed weight lbs (kg) |
||
A |
B |
C |
|||
AG-400 FR H |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
40 (18) |
NRTECH
Table 4: Operating and CIP Parameters (3)
Typical Operating Pressure |
200 psi (1,380 kPa) |
Typical Operating Flux |
10-20 GFD (15-35 LMH) |
Maximum Operating Pressure |
600 psi (4,137 kPa) |
Maximum Temperature |
Continuous operation: 122°F(50°C) Clean-In-Place (CIP):122°F (50°C) |
pH Range |
Optimum rejection: 7.0-7.5 Continuous operation 2.0-11.0 Clean-In-Place (CIP): |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa)Per housing: 50 psi (345 kPa) |
Chlorine Tolerance |
1,000+ ppm-hours, dechlorination recommended |
Feedwater2 |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Refer to Cleaning Guidelines Technical Bulletin TB1194.
Additional Information
• As with any product, use of the products mentioned in this publication in a given application must be tested (including field testing, etc.) by the user in advance to determine suitability.
• Treat RO elements with care; do not drop the element.
• Each RO element is wet tested, preserved in a 1% weight sodium bisulfite solution, and vacuum packed in oxygen barrier bags.
• During storage, avoid freezing and direct sunlight. The temperature should be below 35°C (95°F).
After Installation
• Keep the RO elements wet and use a compatible preservative for storage duration longer than 7 days.
• During the initial start-up, discharge the first permeate to drain for 30 minutes.
• Permeate back pressure should not exceed feed pressure at any time.
• The RO elements shall be maintained in a clean condition, unfouled by particulate matter or precipitates or biological growth.
• Consider cleaning, if the pressure drop increases by 20% or water permeability decreases by 10%. Use only chemicals which are compatible with the membrane.
NRTECH
AG FR Series FACT SHEET
Fouling resistant brackish water RO elements for challenging water & wastewater
The A-Series family of proprietary thin-film reverse osmosis elements is characterized by high flux and relatively high sodium chloride rejection.
The AG FR element is designed for challenging water & wastewater applications. The element construction enhances feed flow to minimize fouling and optimizeenergy performance. In addition, AG FR elements enable more effective cleaning cycles and reduce cleaning frequency as well as the need for harsh chemicals.
Table 1: Element Specification
Membrane |
A-Series, thin-film membrane (TFM) |
Model |
Average |
Average NaCl Rejection (1)(2) |
Minimum NaCl Rejection (1)(2) |
AG4040FM FR,34 |
2,200 (8.8) |
99.5% |
99.0% |
AG8040F-400 |
11,000 (41.6) |
99.5% |
99.1% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.
Testing conditions: 2,000 ppm NaCl solution at 225 psi (1,551 kPa) operating pressure, 77°F (25°C), pH 7.5 and 15% recovery.
Table 2: Element Properties (3)
Model |
Membrane Area ft2 (m2) |
Outer Wrap |
Feed Spacer (mil) |
Part Number |
AG4040FM FR,34 |
80 (7.4) |
Fiberglass |
34 |
3154063 |
AG8040F-400 FR,34 |
400 (37.2) |
Fiberglass |
34 |
3136931 |
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
Table 3: Dimensions and Weight (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed |
||
A |
B |
C |
Weight lbs. (kg) |
||
AG4040F MFR,34 |
Male |
40.0 (101.6) |
0.75 (1.90) |
3.9 (9.9) |
11 (5) |
AG8040 F-400 FR,34 |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
NRTECH
Table 4: Operating and CIP Parameters (3)
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Refer to Cleaning Guidelines Technical Bulletin TB1194.
Typical Operating Pressure |
200 psi (1,379 kPa) |
Typical Operating Flux |
10-20GFD (15-35LMH) |
Maximum OperatingPressure |
600 psi (4,137 kPa) |
Maximum Temperature |
Continuous operation: 122°F (50°C)Clean-In-Place (CIP): 122°F (50°C) |
pH Range |
Optimum rejection: 7.0-7.5, Continuous operation: 2.0-11.0, Clean-In-Place (CIP): 1.0-13.0 (4) |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa)Per housing: 50 psi (345 kPa) |
Chlorine Tolerance |
1,000+ ppm x hours, Dechlorination recommended |
Feedwater |
NTU < 1 SDI15 < 5 |
NRTECH
AG LE Series FACT SHEET
Low Energy Brackish Water RO Elements
The AG LE Series of thin-film reverse osmosis (RO) elements are designed to perform in brackish water applications where the customer and application seek to optimize energy performance with high rejection. AG LE Series elements optimize Veolia chemistry and manufacturing advancements to deliver differentiated performance over the life of the element.
Table 1: Element Specification
Membrane |
Thin-film membrane, polyamide |
||
|
|||
Model |
Average permeate flow gpd (m3/day) (1,2) |
Typical NaCl rejection (1,2) |
Minimum NaCl rejection (1,2) |
AG8040F-400 LE |
8,500 (32.2) |
99.0% |
98.5% |
AG8040F-440 LE |
9,100 (34.5) |
99.0% |
98.5% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary with a minimum of 6,800 gpd (25.7 m3/day) for the AG8040F- 400 LE and 7,280 gpd (27.6 m3/day) for the AG8040F-440 LE.
(2) Testing conditions: 2,000 ppm NaCl solution at 150 psi (1,034 kPa) operating pressure, 77°F (25°C), pH 7 and 15% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Part number |
AG8040F-400 LE |
400 (37.2) |
Fiberglass |
3160987 |
AG8040F-440 LE |
440 (40.9) |
Fiberglass |
3194309 |
Figure 1: Element Dimensions Diagram – Female
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed weight lbs (kg) |
||
A |
B |
C |
|||
AG8040F- 400LE |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 20.1) |
35 (16) |
AG8040F- 440LE |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
Table 4: Operating and CIP Parameters (3)
Typical Operating Pressure |
150 psi (1,034 kPa) |
Typical Operating Flux |
10-20 GFD (15-35 LMH) |
Maximum Operating Pressure |
600 psi (4,137 kPa) |
Maximum Temperature |
Continuous operation: 113°F (45°C) |
pH Range |
Continuous operation 2.0-11.0, Clean-In-Place (CIP): |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa) |
Chlorine Tolerance |
1,000+ |
Feedwater |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Please refer to Cleaning Guidelines Technical Bulletin TB1194.
NRTECH
AG LE H Series FACT SHEET
High performance, low energy, high rejection brackish water RO elements
The AG LE H Series of thin-film reverse osmosis (RO) elements are designed to perform in brackish water applications where the customer andapplication seek to balance low energy and high rejection requirements. AG LE H Series elements optimize Veolia chemistry and manufacturing advancements to deliver differentiated performance over the life of the element. In contrast to ultra-low energy AK H Series, the AG LE H Series elements are often used with the need to control flux due to increased risk of fouling such as when a surface water source is used.
All AG LE H Series elements have NSF/ANSI/CAN 61 certification.
Table 1: Element Specification
Membrane |
Thin-film membrane (TFM), polyamide |
Model |
Average permeate flow gpd (m3/day) (1,2) |
Typical NaCl rejection (1,2) |
Minimum NaCl rejection (1,2) |
AG-400 LE H |
10,000 (37.9) |
99.5% |
99.0% |
AG-440 LE H |
11,000 (41.6) |
99.5% |
99.0% |
(1)Average salt rejection after 24 hours of operation. Individual flow rate may vary with a minimum of 8,000 gpd (30.3 m3/day) for the AG-400 LE H and 8,800 gpd (33.3 m3/day) for the AG-440 LE H.
(2) Testing conditions: 2,000 ppm NaCl solution at 150 psi (1,034 kPa) operating pressure, 77°F (25°C), pH 7 and 15% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Feed Spacer (mil) |
Part number |
AG-400 LE H |
400 (37.2) |
Fiberglass |
34 |
3187569 |
AG-440 LE H |
440 (40.9) |
Fiberglass |
28 |
3187650 |
Figure 1: Element Dimensions Diagram – Female
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed weight lbs (kg) |
||
A |
B |
C |
|||
AG-400 LE H |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
40 (18) |
AG-440 LE H |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
42 (19) |
NRTECH
Table 4: Operating and CIP Parameters (3)
Typical Operating Pressure |
150 psi (1,034 kPa) |
Typical Operating Flux |
10-20 GFD (15-35 LMH) |
Maximum Operating Pressure |
600 psi (4,137 kPa) |
Maximum Temperature |
Continuous operation: 122°F |
pH Range |
Optimum rejection: 7.0-7.5 Continuous operation: 2.0-11.0 Clean-In-Place (CIP): |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa) |
Chlorine Tolerance |
1,000+ ppm-hours, dechlorination recommended |
Feedwater |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Please refer to Cleaning Guidelines Technical Bulletin TB1194.
Additional Information
• As with any product, use of the products mentioned in this publication in a given application must be tested (including field testing, etc.) by the user in advance to determine suitability.
• Treat RO elements with care; do not drop the element.
• Each RO element is wet tested, preserved in a 1% weight sodium bisulfite solution, and vacuum packed in oxygen barrier bags.
• During storage, avoid freezing and direct sunlight. The temperature should be below 35°C (95°F).
After Installation
· Keep the RO elements wet and use a compatible preservative for storage duration longer than 7 days.
· During the initial start-up, discharge the first permeate to drain for 30 minutes.
· Permeate back pressure should not exceed feed pressure at any time.
· The RO elements shall be maintained in a clean condition, unfouled by particulate matter or precipitates or biological growth.
· Consider cleaning, if the pressure drop increases by 20% or water permeability decreases by 10%. Use only chemicals which are compatible with the membrane.
NRTECH
HL Series FACT SHEET
Water Softening NF Elements
The H-Series proprietary thin-film nanofiltration membrane elements are characterized by an approximate molecular weight cut-off of 200-400 daltons for uncharged organic molecules. Divalent and multivalent ion rejection is dependent upon feed concentration and composition.
HL Nanofiltration Elements are used for water softening, color removal, and reduction of THM formation potential.
Table 1: Element Specification
Membrane |
H-Series, Thin-film membrane (TFM) |
Model |
Average Permeate Flow gpd (m3/day) (1)(2) |
Average Rejection (1)(2) |
Minimum Rejection (1)(2) |
HL2540FM |
840 (3.2) |
99.5% |
98.0% |
HL4040FM |
2,700 (10.2) |
99.5% |
98.0% |
HL8040F-400 |
13,000 (49.2) |
99.5% |
98.0% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.
(2) Testing conditions: 2,000ppm MgSO4 solution at 110psi (760kPa) operating pressure, 77°F, pH7.5 and 15% recovery.
Table 2: Element Properties (3)
Model |
Active Area ft2 (m2) |
Outer Wrap |
Part Number |
HL2540FM |
27 (2.5) |
Fiberglass |
1207230 |
HL4040FM |
90 (8.4) |
Fiberglass |
1207236 |
HL8040F-400 |
400 (37.2) |
Fiberglass |
1207240 |
Figure 1: Element Dimensions Diagram (Female)
Figure 2: Element Dimensions Diagram (Male)
Table 3: Dimensions and Weight (3)
Model |
|
Dimensions, Inches (cm) |
Boxed |
||
Type |
A |
B |
C |
Weight lbs. (kg) |
|
HL2540 |
Male |
40.0 (101.6) |
0.75 (1.90) |
2.4 (6.1) |
5 (2.3) |
HL4040 |
Male |
40.0 (101.6) |
0.75 (1.90) |
3.9 (9.9) |
8 (3.5) |
HL8040 |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
32 (14.5) |
NRTECH
Table 4: Operating and CIP Parameters (3)
Typical Operating Pressure |
60-300psi (483-2,069kPa) |
Typical Operating Flux |
10-20GFD (15-35LMH) |
Maximum OperatingPressure |
600psi (4,140kPa) |
Maximum Temperature |
Continuous operation: 122°F (50°C)Clean In Place (CIP): 104°F (40°C) |
pH Range |
Optimum rejection: 6.0-7.0 Continuous operation: 3.0-9.0, Clean In Place (CIP): 2.0-11.0 (4) |
Maximum Pressure Drop |
Over an element: 12psi (83kPa)Per housing: 50psi (345kPa) |
Chlorine Tolerance |
1,000+ ppm x hours, dechlorination recommended |
Feedwater |
NTU < 1 SDI15 < 5 |
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Please refer to Cleaning Guidelines Technical Bulletin TB1194.
NRTECH
AC Series FACT SHEET
Very high rejection seawater RO elements
The AC Series, family of proprietary thin film reverse osmosis membrane elements, is characterized by an excellent sodium chloride rejection. AC Series is selected when high quality permeate is demanded from seawaterthat is relatively high in TDS.
AC Series new membrane chemistry provides excellent rejection characteristics when operated at seawater operating conditions (pressures exceeding 800psi (5,516kPa) and elevated temperatures).
Table 1: Element Specification
Membrane |
A-series, thin-film membrane (TFM*) |
Model |
Average Permeate Flow Gpd (m3/day) (1)(2) |
Ave. NaCl Rejectio n (1)(2) |
Min. NaCl Rejection (2) |
Min. Boron Rejection (2) |
AC-400, 34 |
5800 (21.9) |
99.85% |
99.5% |
96.0% |
AC-440 |
6400 (24.2) |
99.85% |
99.5% |
96.0% |
(1) Average salt rejection after
24 hours of operation. Individual flow rate may vary ±20%.
(2) Testing conditions: 32,000mg/l NaCl &
5mg/l Boron solution at 800psi (5,516kPa) operating
pressure, 77°F (25°C), pH 8.0 and 7% recovery.
Model |
Active Area ft2 (m2) |
Outer Wrap |
Part Number |
AC-400, 34 |
400 (37.2) |
Fiberglass |
3154588 |
AC-440 |
440 (40.9) |
Fiberglass |
3157144 |
Figure 1: Element Dimensions Diagram – Female
Table 2: Operating and CIP Parameters
Typical Operating Pressure |
800psi (5,516kPa) |
Typical Operating Flux |
7-11GFD (12-19LMH) |
Maximum Operating Pressure |
1,200psi (8,274kPa) |
Maximum Temperature |
Continuous operation: 122°F (50°C) Clean-In-Place (CIP): 122°F (50°C) |
pH range |
Optimum rejection pH: 7.0-7.5, Continuous operation: 2.0-11.0, Clean-In-Place (CIP): 1.0 – 12.0 (1) |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa) Per housing: 50 psi (345 kPa) |
Chlorine Tolerance |
1,000+ ppm-hours, dechlorination recommended |
Feedwater |
NTU < 1 SDI15 < 5 |
(1) Refer to Cleaning Guidelines Technical Bulletin TB1194.
Table 3: Dimensions and Weights
Model |
Type |
Dimensions, inches (cm) |
Boxed |
||
A |
B |
C |
Weight lbs (kg) |
||
AC-400, 34 |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
AC-440 |
Female |
40.0 (101.6) |
1.125 (2.86) |
7.9 (20.1) |
35 (16) |
NRTECH
AD Series FACT SHEET
High rejection seawater RO element
The AD Series family of proprietary thin film reverseosmosis elements is characterized by an excellent sodium chloride rejection. The AD Series is selected when high quality permeate is demanded from seawater that is relatively high in TDS.
AD Series membrane chemistry provides excellent rejection characteristics when operated at seawater operating conditions (pressures exceeding 800 psi (5,516kPa) and elevated temperatures).
Table 1: Element Specification
Membrane |
Thin-film membrane (TFM) |
Model |
Average permeate flow (m3/day) (1)(2) |
Average NaCl rejection (1)(2) |
Minimum NaCl rejection (1)(2) |
Typical boron (2) |
AD-90 |
1375 (5.2) |
99.8% |
99.5% |
95.0% |
AD-400,34 |
7000 (26.5) |
99.8% |
99.5% |
95.0% |
AD-440 |
7700 (29.2) |
99.8% |
99.5% |
95.0% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.
(2) Testing conditions: 32,000mg/l NaCl & 5mg/l boron solution at 800psi (5,516kPa) operating pressure, 77°F (25°C), pH 8.0 and 7% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Part number |
AD-90 |
90 (8.4) |
Fiberglass |
3056651 |
AD-400,34 |
400 (37.2) |
Fiberglass |
3056654 |
AD-440 |
440 (40.9) |
Fiberglass |
3056655 |
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed Weight lbs. (kg) |
||
A |
B |
C |
|||
AD-90 |
Male |
40.0 |
0.75 |
3.9 |
9 |
(101.6) |
(1.90) |
(9.9) |
(4) |
||
AD-400, |
Female |
40.0 |
1.125 |
7.9 |
35 |
34 |
(101.6) |
(2.86) |
(20.1) |
(16) |
|
AD-440 |
Female |
40.0 |
1.125 |
7.9 |
35 |
(101.6) |
(2.86) |
(20.1) |
(16) |
NRTECH
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Ut elit tellus, luctus nec ullamcorper mattis, pulvinar dapibus leo.
(3) Element properties and parameters are indicative numbers. Specific values by element may vary within normal element manufacturing tolerances.
(4) Refer to Cleaning Guidelines Technical Bulletin TB1194.
Typical Operating Pressure |
800psi (5,516kPa) |
Typical Operating Flux |
7-11GFD (12-19LMH) |
Maximum Operating Pressure |
1,200psi (8,274kPa) |
Maximum Temperature |
Continuous operation: 122°F (50°C) Clean-In-Place (CIP): 122°F (50°C) |
pH Range |
Optimum rejection: 7.0-7.5, Continuous operation 2.0-11.0, Clean-In-Place (CIP): 1.0-12.0 (4) |
Maximum Pressure Drop |
Over an element: 15 psi (103 kPa) Per housing: 50 psi (345 kPa) |
Chlorine Tolerance |
1,000+ ppm-hours, dechlorination recommended |
Feedwater |
NTU < 1 SDI15 < 5 |
NRTECH
AE Series FACT SHEET
High rejection low energy seawater RO elements
The AE series of proprietary thin film reverse osmosis elements are characterized by an excellent sodium chloride rejection. AE series is selected when high quality permeate is demanded from seawater that is relatively high in TDS.
AE series membrane chemistry provides excellent rejection characteristics when operated at seawater operating conditions (pressures exceeding 800psi (5,516kPa).
Table 1: Element Specification
Membrane |
Thin-film membrane (TFM) |
Model |
Average permeate flow |
Ave. NaCl rejection (1) (2) |
Min. NaCl rejection (1) (2) |
Min. Boron Rejection (2) |
AE-90 |
1875 (7.1) |
99.8% |
99.5% |
92.0% |
AE-400, 34 |
9000 (34.1) |
99.8% |
99.5% |
92.0% |
AE-440 |
9900 (37.5) |
99.8% |
99.5% |
92.0% |
(1) Average salt rejection after 24 hours of operation. Individual flow rate may vary ±20%.
(2) Testing conditions: 32,000mg/l NaCl & 5mg/l Boron solution at 800psi (5,516kPa) operating pressure, 77°F (25°C), pH 8.0 and 10% recovery.
Table 2: Element Properties (3)
Model |
Active area ft2 (m2) |
Outer wrap |
Part number |
AE-90 |
90 (8.4) |
Fiberglass |
3056660 |
AE-400, 34 |
400 (37.2) |
Fiberglass |
3056662 |
AE-440 |
440 (40.9) |
Fiberglass |
3056663 |
Figure 1: Element Dimensions Diagram – Female
Figure 2: Element Dimensions Diagram – Male
Table 3: Dimensions and Weights (3)
Model |
Type |
Dimensions, inches (cm) |
Boxed Weight lbs (kg) |
||
A |
B |
C |
|||
AE-90 |
Male |
40.0 |
0.75 |
3.9 |
9 |
(101.6) |
(1.90) |
(9.9) |
(4) |
||